Page 1 of 1
Curious about write/read speeds
Posted: 06 Oct 2008, 15:55
by joost
I'm just being curious about the speeds other people are getting when writing to/reading from Bubba Two internal hd.
When copying from pc to Bubba (1TB WD) over gigabit ethernet (with a Netgear WRN3500 in the middle) I reach somewhere between 6,5 and 7,1 MB/s.
The other way: copying from Bubba to pc is stuck at circa 5,9 MB/s.
How are you faring?
Posted: 11 Oct 2008, 15:09
by essence
I get roughly 5% throughput either way between XP PC to Bubba|Two over a gigabit ethernet with a Netgear GS608 switch in the middle.
(roughly = measured via Windows Task Manager)
Posted: 15 Oct 2008, 11:11
by MartinHageras
I get about 4-5 MB/s copying to Bubba from XP on 100Mbit and through my Linksys router using FTP.
Posted: 17 Oct 2008, 07:20
by Puma
Hello,
I'm getting 6 - 6,5 Mb/ps with windows XP to bubba and in between a Gigabit switch make NETGEAR
Is better performance possible??
Puma
Posted: 17 Oct 2008, 07:35
by carl
Puma wrote:Hello,
I'm getting 6 - 6,5 Mb/ps with windows XP to bubba and in between a Gigabit switch make NETGEAR
Is better performance possible??
Puma
do you mean Megabit or Megabyte there?
/Carl
Posted: 18 Oct 2008, 06:32
by squadra
wireless network: WRT54GC
ftp transfer from bubba to PC : around 24 Mbps
ftp transfer from PC to bubba: arround 10 Mbps
Received 11760168 bytes in 4.6 secs, (24.68 Mbps), transfer succeeded
Not even 3 Megabytes per second using wireless, i guess i have to wire some pc's or know what settings to tweak.
Posted: 19 Oct 2008, 11:33
by carl
The current speeds I get from a bubbatwo I have here via FTP is 9 MB/s download and 6.76MB/s upload. Things like samba will go much faster when we will activate the crypto module in the processor.
/Carl
Posted: 25 Oct 2008, 19:23
by joost
Hi Carl, any idea when to expect the crypto-module-activation-update? And how much of a speed increase could that give?
Thanks!
Posted: 20 Nov 2008, 07:36
by squadra
After all updates my file tranferr is 5 times lower
past: ftp transfer from bubba to PC : around 24 Mbps
now: ftp transfer from bubba to PC : around 5 Mbps (megabit...)
same network configuration... Transferring data to another mounted disk takes a whole day
((
Posted: 21 Nov 2008, 01:37
by pa
Something does not seem right...
Can you provide us with your setup?
Are you using just LAN?
Wired/wireless?
If wired, gigabit network or 100Mbit?
Bubba as dhcp server?
All updates, does that mean you have updated the bootloader + lastet updates for linux?
/PA
Posted: 21 Nov 2008, 11:26
by squadra
Im using it in LAN (router is my dhcp server: network scenario 6 in manual). Wireless gigabit connection (apple). But even if i mount an external USB drive to bubba it transfers very slow. In the past i got half of capacity of my network but now not anymore.
I updated starting from scratch. Then i got one error message concerning PHP on which i opened a post concerning update on this forum. All i experience is something bad with firefly (it crashes) but nothing i can relate to slow transferr speed.
I did:
apt-get update
apt-get dist-upgrade
/usr/sbin/ethtool -K eth1 rx off tx off
(and fixt shis in init.d)
Bootloader upgrade
And i don't have installed other things like subversion to find out where it goes wrong. I can give you ssh access because for me the log is abracadabra.
Thanks, Maarten
Posted: 24 Nov 2008, 03:13
by pa
Can you have the USB-drive connected and send me an email with account information?
/PA
Posted: 24 Nov 2008, 10:59
by squadra
THANKS PA!!!
It seems i don't have to use windows explorer to copy files wireless (even when i copy to attached usb storrage), using linux command goes faster and wired my ftp rate is arround 72MBps (wireless it is 15-28 depending which computer or time or whatever) so this is not a bubba issue
