Re: External USB drive & B3.
Posted: 31 Oct 2010, 11:53
yes
This could very well be the case.For me it turned out that it was the USB cable that was causing the problem.
Code: Select all
USB port nn disabled by hub (EMI?), re-enabling
Code: Select all
niklas@b3:~$ sudo /etc/init.d/apcupsd stop
niklas@b3:~$ sudo tail -n 22 /var/log/syslog
Apr 30 17:01:21 b3 apcupsd[1766]: apcupsd exiting, signal 15
Apr 30 17:01:21 b3 apcupsd[1766]: apcupsd shutdown succeeded
Apr 30 17:01:27 b3 kernel: [147854.228130] usb 1-1.1: USB disconnect, device number 3
Apr 30 17:01:42 b3 kernel: [147869.563842] usb 1-1.1: new high speed USB device number 9 using orion-ehci
Apr 30 17:01:42 b3 kernel: [147869.718475] scsi9 : usb-storage 1-1.1:1.0
Apr 30 17:01:42 b3 mtp-probe: checking bus 1, device 9: "/sys/devices/platform/orion-ehci.0/usb1/1-1/1-1.1"
Apr 30 17:01:42 b3 mtp-probe: bus: 1, device: 9 was not an MTP device
Apr 30 17:01:43 b3 kernel: [147870.724339] scsi 9:0:0:0: Direct-Access Seagate Backup+ BK 0409 PQ: 0 ANSI: 6
Apr 30 17:01:43 b3 kernel: [147870.733090] sd 9:0:0:0: Attached scsi generic sg5 type 0
Apr 30 17:01:43 b3 kernel: [147870.741812] sd 9:0:0:0: [sde] 1953525167 512-byte logical blocks: (1.00 TB/931 GiB)
Apr 30 17:01:43 b3 kernel: [147870.756816] sd 9:0:0:0: [sde] Write Protect is off
Apr 30 17:01:43 b3 kernel: [147870.761720] sd 9:0:0:0: [sde] Mode Sense: 4f 00 00 00
Apr 30 17:01:43 b3 kernel: [147870.761730] sd 9:0:0:0: [sde] Assuming drive cache: write through
Apr 30 17:01:43 b3 kernel: [147870.778280] sd 9:0:0:0: [sde] Assuming drive cache: write through
Apr 30 17:01:43 b3 kernel: [147870.814957] sde: sde1 sde2
Apr 30 17:01:43 b3 kernel: [147870.822537] sd 9:0:0:0: [sde] Assuming drive cache: write through
Apr 30 17:01:43 b3 kernel: [147870.828759] sd 9:0:0:0: [sde] Attached SCSI disk
Apr 30 17:01:44 b3 kernel: [147871.080757] sd 9:0:0:0: [sde] Sense Key : 0x1 [current] [descriptor]
Apr 30 17:01:44 b3 kernel: [147871.087317] Descriptor sense data with sense descriptors (in hex):
Apr 30 17:01:44 b3 kernel: [147871.093580] 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00
Apr 30 17:01:44 b3 kernel: [147871.100129] 00 00 00 00 00 50
Apr 30 17:01:44 b3 kernel: [147871.104011] sd 9:0:0:0: [sde] ASC=0x4 ASCQ=0x1d
niklas@b3:~$ mkdir -p mnt/usb_fat && mkdir -p mnt/usb_ext4
niklas@b3:~$ sudo mount -t vfat /dev/sde1 mnt/usb_fat
niklas@b3:~$ sudo mount -t ext4 /dev/sde2 mnt/usb_ext4
niklas@b3:~$ df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda1 11G 4.7G 5.7G 46% /
tmpfs 252M 0 252M 0% /lib/init/rw
udev 10M 276K 9.8M 3% /dev
tmpfs 252M 4.0K 252M 1% /dev/shm
/dev/mapper/bubba-storage
6.9T 5.0T 1.5T 78% /home
popcorn:/opt/sybhttpd/localhost.drives/HARD_DISK/Video
917G 865G 52G 95% /home/storage/mounts/popcorn
/dev/sde1 391G 956M 390G 1% /home/niklas/mnt/usb_fat
/dev/sde2 533G 263G 243G 52% /home/niklas/mnt/usb_ext4
niklas@b3:~$ sudo smartctl -a /dev/sde
smartctl 6.0 2012-10-10 r3643 [armv5tel-linux-2.6.39.4-11] (local build)
Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus SpinPoint M8 (AF)
Device Model: ST1000LM024 HN-M101MBB
Serial Number: S2TPJ9CC786300
LU WWN Device Id: 5 0004cf 207fc5eb6
Firmware Version: 2AR10001
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Apr 30 17:15:04 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13140) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 219) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 0
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 086 085 025 Pre-fail Always - 4460
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 171
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 118
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 169
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 1
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 055 000 Old_age Always - 30 (Min/Max 20/46)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 96
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1256
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.